Saturday, January 19, 2013

Taggy Blanket

I've made a few of these taggy blankets as gifts and everyone always loves them. The idea is that babies usually rotate their blankets to find the tag and suck on it - with this blanket, there are tags everywhere!

   
Materials:
  • Soft fabric for backing (minky, fleece, I used dimple minky for a little bit of texture)
  • Cute pattern fabric for the top
  • A few different color ribbons (fabric ribbon only, no wires. I used 4 different ribbons that matched my pattern fabric.)
Instructions:

Cut your fabric to size, I cut mine to 18.5" by 18.5". I cut the minky a little bit larger and then serged the edges to get it down to 18.5".

Next cut your ribbons to size, I cut mine to 5" long. I used 32 pieces of ribbon (8 of each color). I placed them around the edges to get a sense of the spacing, leave a little bit of room around the corners so it's not too crowded.

Fold each ribbon in half and pin it on top of the patterned fabric - the patterned fabric should be face up and the edges of the ribbon should be lined up with the edge of the fabric.

Sew along the edge 1/4" in. Once you've sewn around all 4 sides, place the backing fabric right side down on top of your patterned fabric.

Sew along the edge 1/2" in, make sure to leave a few inches open on one side so that you can flip the blanket.




Flip the blanket right side out and sew along the edge 1/4" in. Make sure you close up the hole that you used for flipping.

And now you're done!


Saturday, January 12, 2013

Wet Bikini Bag

This project is a nifty little waterproof bag - you put the wet stuff in it, your other stuff stays dry :) I'm making some of these as "wet bikini bags" for traveling to the beach, but you could use it for anything.


Materials:
  • Pretty fabric for the outside - cotton prints or interior design fabric does well
  • Waterproof fabric (I used vinyl, but you could use oil cloth or even a shower curtain).
  • A 14" Zipper (my finished bag is about 12.5" by 10.5")
  • OPTIONAL opaque fabric for lining (I used this because I used clear vinyl and a 1-sided print, this covers up the back side of the outer fabric)
Instructions:

 Cut out two 11"x13" pieces of each fabric. Here are all of my materials ready to get sewing (the clear vinyl still has the tissue paper on it):


Next layer the outer fabric (face up), zipper (face down), waterproof fabric (face down if it has a side), and inner fabric (face down if it has a side). The outer edges should be aligned:

If you feel like being careful, pin near the edge to keep the fabrics from slipping. Sew along the edge, 1/4" in from the side.

Flip all of the fabric right side out and repeat the process for the other side, you should end up with something that looks like this:





Now unzip the zipper half way (that's important so you can flip the bag!!!) and fold the like fabrics so the right side is facing each other - the outer fabric should be together and the lining fabrics should be together. Sew around the edges, leaving a whole along the bottom of the lining to flip the bags:

To give the bag some depth you can miter corners, I think it looks really nice. Start by folding the corner of the bag like this (so the seam runs down the diagonal). Make sure that the seam on top and the seem on bottom are directly on top of one another:

Then sew a line across the corner, perpendicular to the seam:

Then trim the excess fabric:

Miter the corners of the lining and the outer fabric. Then flip the bag right side out:

Sew up the whole at the bottom of the lining. My stitching is a bit messy, since I started sewing on just the vinyl and it was sticking to my sewing machine - I ended up using the tissue paper so the vinyl would slide along better, then tearing it away after the seam was sewn:

Now push the lining into the bag, and you're done!